Welcome to our website.

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

Our enterprise since its inception, often regards solution excellent as enterprise life, continually strengthen output technology, enhance product high quality and continually strengthen organization total high-quality administration, in strict accordance using the national standard ISO 9001:2000 for Circuit Card Assemblies, Electronic Board Design, Easyeda Pcb, We have deep cooperation with hundreds of factories around China. The products we provide can match with your different demands. Choose us, and we won't make you regret!
Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics Detail:

Basic Rules of PCB Layout

1. Layout according to the circuit module, the related circuits that realize the same function are called a module, the components in the circuit module should adopt the principle of nearest concentration, and the digital circuit and the analog circuit should be separated;
2. Components and devices must be mounted within 1.27mm around non-mounting holes such as positioning holes and standard holes, and no components shall be mounted within 3.5mm (for M2.5) and 4mm (for M3) around mounting holes such as screws;
3. Avoid placing vias below components such as horizontally mounted resistors, inductors (plug-ins), and electrolytic capacitors to avoid short circuits between the vias and the component shell after wave soldering;
4. The distance between the outside of the component and the edge of the board is 5mm;
5. The distance between the outside of the mounted component pad and the outside of the adjacent mounted component is greater than 2mm;
6. Metal shell components and metal parts (shielding boxes, etc.) cannot touch other components, and cannot be close to printed lines and pads, and the spacing should be greater than 2mm. The size of the positioning holes, fastener installation holes, elliptical holes and other square holes in the plate is greater than 3mm from the edge of the plate;
7. The heating element cannot be close to the wire and the thermal element; the high-heating element should be evenly distributed;
8. The power socket should be arranged around the printed board as much as possible, and the bus bar terminals connected to the power socket should be arranged on the same side. Special care should be taken not to arrange power sockets and other soldered connectors between the connectors, in order to facilitate the soldering of these sockets and connectors, and the design and tying of power cables. The arrangement spacing of power sockets and welding connectors should be considered to facilitate the insertion and removal of power plugs;
9. Arrangement of other components:
All IC components are unilaterally aligned, the polarity of polar components is clearly marked, and the polarity marking on the same printed board should not be more than two directions. When two directions appear, the two directions are perpendicular to each other;
10. The wiring on the board should be properly dense. When the difference in density is too large, it should be filled with mesh copper foil, and the mesh should be greater than 8mil (or 0.2mm);
11. There should be no through-holes on the patch pads, so as to avoid the loss of solder paste and cause the components to be soldered. Important signal lines are not allowed to pass between the socket pins;
12. The patch is unilaterally aligned, the character direction is the same, and the packaging direction is the same;
13. For devices with polarity, the direction of polarity marking on the same board should be as consistent as possible.

PCB Component Routing Rules

1. In the area where the wiring area is less than or equal to 1mm from the edge of the PCB, and within 1mm around the mounting hole, wiring is prohibited;
2. The power line should be as wide as possible and should not be less than 18mil; the signal line width should not be less than 12mil; the cpu input and output lines should not be less than 10mil (or 8mil); the line spacing should not be less than 10mil;
3. The normal via is not less than 30mil;
4. Dual in-line: pad 60mil, aperture 40mil;
1/4W resistor: 51*55mil (0805 surface mount); when in-line, the pad is 62mil, and the aperture is 42mil;
Electrodeless capacitor: 51*55mil (0805 surface mount); when plugged directly, the pad is 50mil, and the aperture is 28mil;
5.Note that the power wire and the ground wire should be as radial as possible, and the signal wire should not be looped.

Factory Show

P-D-1


Product detail pictures:

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures

Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics detail pictures


Related Product Guide:

Control the quality by the details, show the strength by quality. Our company has strived to establish a highly efficient and stable staff team and explored an effective quality control process for Custom Power Circuit Board Factories - Custom Fr-4 Circuit Board Pcb Board – Weilian Electronics , The product will supply to all over the world, such as: Sao Paulo, Haiti, Slovenia, Our Company policy is quality first, to be better and stronger, sustainable development . Our pursuit goals is for society, customers, employees, partners and enterprises to seek reasonable benefit. We aspirate to do cooperate with all different the auto parts manufacturers, repair shop, auto peer , then create a beautiful future! Thank you for taking time to browse our website and we would welcome any suggestions you may have that can help us to improve our site.
  • Speaking of this cooperation with the Chinese manufacturer, I just want to saywell dodne, we are very satisfied.
    5 Stars By Sandra from Senegal - 2017.09.26 12:12
    The factory technical staff not only have high level of technology, their English level is also very good, this is a great help to technology communication.
    5 Stars By Pearl Permewan from Estonia - 2018.09.23 17:37
    Write your message here and send it to us